螺釘用干燥固體潤滑膜

Dry solid film lubricant for coating screws

Gleitmo 605 是Gleitmo 白色固體潤滑劑的水基懸浮液, 干燥的潤滑膜使用在不同的物質表面有

很好的附著性。

Gleitmo 605 is a colloidal suspension of Gleitmo White Solid Film Lubricants in water.

The dry lubricating film remaining upon application shows a very good adhesion on the different surfaces types.

應用范圍 Field o**n：

Gleitmo 605 適用于螺釘﹑螺帽﹑木螺釘﹑刨花板螺釘﹑薄鋼板螺釘﹑固定螺釘(一般來說電子

行業用的各種螺釘)﹑切割環形接口用螺帽等的潤滑。

Gleitmo 605 is used for lubrication of threaded screws, nuts, wood screws, chipboard screws, sheet metal screws; clamping screws (generally all screws for the electrical industry) cap nuts for cutting ring joints.

x 溫度范圍: - 40/ + 110℃ Temperature range : - 40/ + 110℃

x 滿足自動化工業生產(VDA)用螺釘?shù)臐櫥枰?

Meets the requirements of the automotive industry (VDA) for screw lubrication

x 特別適用于大批量小零件 Is especially suitable for bulk small parts

x 節省裝配時間, 特別適用于自動螺釘裝配系統

Saves on assembly time and is particularly well suited for automatic screw-driving systems

x 清澈﹑不含油脂

Is clean and non-greasing

x 與各種材料都有良好的表面附著性

Has a very good surface adhesion on all materials

x 不影響螺帽鎖緊系統的效率

Will not affect the efficiency of screw locking systems

x 利于環保, 對使用者無害

Is environmentally and consumer friendly

x 潤滑膜性能通過德國飲用水法認證

Curred film is approved for lubrication in contact with drinking water (German Drinking Water Legislation)

x 含一種 UV 添加劑﹐通過 UV 燈(340-380nm)進行涂層控制

Is containing an UV-illumination additive for coating control by means of UV-light (340-380 nm)

使用方法 Method o**n ：

由于摩擦的需要, Gleitmo 605 可用水稀釋 (水質需達到飲用水標準)。 通常, Gleitmo 605 的稀釋比例為1:3 (離心涂程序的嚴格要求)至1:7 (滴涂)。 稀釋時, 一邊不斷攪拌Gleitmo 605 一邊加水, 在注入浸液時也一樣。 為避免腐蝕, 必須用熱空氣 (約60 ) ℃ 吹干浸處理后的零件。零件在施涂時**含油脂。在非常干燥的條件下包裝零件, 如進行大批量施涂, 采用一般鍍鋅設備較為方便。

Depending on etiologic requirements, Gleitmo 605 can be diluted with water (at least of drinking water quality). As a Rule, Gleitmo 605 is used at a dilution ratio of 1:3 (for centrifuge coating procedures, stringent requirements) and up to 1:7 (for dipping). For dilution, water is added to Gleitmo 605 while constantly stirring. The same procedure should be followed for replenishing the immersion bath. To avoid any risk of corrosion it is most urgently recommended drying the parts immediately after the dipping process by hot air (up to approx. 60 ). ℃ The parts to be coated should be degreased. Packaging of coated parts only in absolutely dry condition. The equipment commonly used in the galvanizing industry has proved to be very convenient in case of large coating quantities.

防止結凍! 在封閉的原裝容器中, 室溫下可貯存12 個月。

Protect against freezing! In closed original containers, at room temperature, storable up to 12 month.